Give me some rope i'm coming loose

whatshouldwecallmichigan:

I have the weirdest boner right now…

Configuring VTP Server:

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname S1

S1(config)#vtp mode server

Device mode already VTP SERVER.

S1(config)#vtp domain example

Changing VTP domain name from NULL to example

S1(config)#vtp password vinita

Setting device VLAN database password to vinita

Configuring VTP Client:

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname S2

S2(config)#vtp mode client

Setting device to VTP CLIENT mode.

S2(config)#vtp domain example

Changing VTP domain name from NULL to example

S2(config)#vtp password vinita

Setting device VLAN database password to vinita

S2(config)#

Configuring VLANS:

Switch>enable

Switch#configure terminal

Switch(config)# vlan 10

Switch1(config-vlan)# name Accounting

Switch1(config-vlan)# end

Configuring Hosts:

!  Assign Ports Fe0/1 and Fe0/2 in VLAN 2

Switch1(config)# interface fastethernet0/1

Switch1(config-if)# switchport mode access

Switch1(config-if)# switchport access vlan 2

Switch1(config-if)# end

Switch1(config)# interface fastethernet0/2

Switch1(config-if)# switchport mode access

Switch1(config-if)# switchport access vlan 2

Switch1(config-if)# end

Configuring Trunking:

S1(config)#interface fastEthernet 0/24

S1(config-if)#switchport mode trunk

S1(config-if)#switchport trunk encapsulation dot1q

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24,

changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24,

changed state to up

S1(config-if)#exit

S1(config)#interface gigabitEthernet 1/1

S1(config-if)#switchport mode trunk

S1(config-if)#exit

S1(config)#interface gigabitEthernet 1/2

S1(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/2,

changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/2,

changed state to up

S1(config-if)#exit

S1(config)#

Configure Intervlan Routing:

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#interface fastEthernet 0/0

Router(config-if)#no ip address

Router(config-if)#no shutdown

Router(config-if)#exit

Router(config)#interface fastEthernet 0/0.10

Router(config-subif)#encapsulation dot1Q 10

Router(config-subif)#ip address 10.0.0.1 255.0.0.0

Router(config-subif)#exit

Router(config)#interface fastEthernet 0/0.20

Router(config-subif)#encapsulation dot1Q 20

Router(config-subif)#ip address 20.0.0.1 255.0.0.0

Router(config-subif)#exit

Configure Spanning Tree so One is the Root:

Switch1(config)#spanning-tree vlan 1 root primary

Switch1(config)#

01:20:59: STP: VLAN0001 we are the spanning tree root

!— Priority is lowered automatically as shown in the output below

Switch1(config)#do show spanning-tree vlan 1    

VLAN0001

  Spanning tree enabled protocol ieee

  Root ID    Priority    24577

             Address     001b.90b4.6900

             This bridge is the root

             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec

  Bridge ID  Priority    24577  (priority 24576sys-id-ext 1)

             Address     001b.90b4.6900

             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec

             Aging Time 15

Configure IP Address:

From the command line, use the enable command to enter privileged EXEC mode.

Use the configure terminal to enter configuration mode.

Enter interface vlan1 to choose the switch interface for configuration.

Use the command ip address [ip_address] [subnet_mask].